Main Shaft Assembly For Cone Crusher
The steps to disassemble the crushing cone are as follows:
1.Remove the adjustment sleeve.
2. Screw the spindle eyebolt to the upper end of the spindle.
3. Use an on-site crane or lifting device to carefully lift the crushing Cone Crusher from the crusher. The wire rope should be lifted when the thick side of the eccentric sleeve is at an angle with the vertical direction. In this figure, use The circle marks the contact part of the main shaft and the main shaft bushing and the direction of the wire rope pulling force. The broken cone under tension or inclined is slightly biased toward the thick side of the eccentric sleeve, so that there is enough space between the seal ring on the body and the bowl-shaped bearing frame. Clearance. Lifting in this way can avoid damage to the sealing device under the body and on the bowl-shaped bearing frame. Before removing the adjustment sleeve, just pay attention to the position of the discharge port to determine the position of the heavy or thick side of the eccentric sleeve. The low side position of the body is the heavy side or thick side position of the eccentric sleeve.
During the disassembly process, be careful not to touch the bowl-shaped bearing frame seal ring with the body seal ring. After the spindle is removed, make sure that the seal ring can be properly placed on the bowl-shaped bearing frame again.
4. After the crushing cone is lifted out of the crusher, check all the polished surfaces of the body and the main shaft, and repair all abrasions or nicks and rust or pitting.
5. In order to operate the dismantled broken wall at a suitable height, it is recommended to open a hole with sufficient depth and size on the floor or ground to place the broken cone. This hole should have corresponding drainage measures to avoid water accumulation Place the broken cone in this hole so that the body skirt sits on the floor or the ground.
Relying on the technical platform of the whole machine, the company provides the following models for customers:
Single-cylinder cone crusher: GGP100, GGP100S, GGP200, GGP200s, GGP300, GGP300S, GGP500, GGP500S, GGP550, GGP11F.
CHS420,CHS430,CHS440,CHS660,CHS870,CHS880,CHS890.CHS895
Multi-cylinder cone crusher: HHP3 , HHP4, HHP5, HHP6, HHP100, HHP200, HHP300, HHP400, HHP500, HHP700, HHP800;.
Heavy hydraulic cone crusher: MMP800, MMP1000, MMP1250.
Jaw crusher: CC80, CC96, CC100, CC106, CC110, CC116 , CC120, CC125, CC130, CC140, CC145, C160.
CJ612,CJ613,CJ615,CJ618
Shenyang Tianyi Mining Machinery Co., Ltd. provides thousands of spare parts for all the above models, such as: uniform feeding device, safety guard, fixed cone feeding hopper, locking ring, adjusting ring, fixed cone, main frame, spherical tile, Eccentric sleeve bushing, drive shaft, drive shaft sleeve, big gear, pinion gear, main shaft, eccentric sleeve, eccentric sleeve thrust bearing, iron release assembly, counterweight guard plate, moving cone lower bushing, anti-rotation device , Moving cone, moving cone upper bushing, moving cone liner, fixed cone plate, fixed cone liner, fasteners, distribution plate, locking screw, moving cone sphere, locking cylinder, cutting ring, feeding plate , Adjusting cap, large gear ring, fixed cone liner bolts, adapter ring, main frame seat cushion, release cylinder, moving cone upper copper sleeve, T-seal, moving cone lower copper sleeve, main frame guard plate, rib guard plate, U-shaped seal, lower thrust bearing, distribution plate bolt, locking bolt, dust cover, main frame pin, moving cone ball pin, spherical tile holder, eccentric steel sleeve, eccentric copper sleeve, counterweight, upper thrust bearing, horizontal Axle box, horizontal shaft frame guard plate, horizontal shaft box cover, fuel tank, horizontal shaft copper sleeve, hydraulic motor assembly; main frame assembly, fixed cone assembly, spherical bearing assembly, eccentric sleeve, counterweight, gear assembly Assembly, adjusting ring assembly, moving cone assembly, horizontal shaft assembly, distribution tray assembly.
Contact Now
